Kinematics · Part 1 of 4
Position, velocity and acceleration
Learn what position, velocity and acceleration mean, how they relate through slopes, and how to read motion from graphs and signs.
Kinematics19 min read
A car's GPS shows one number: how far you are along the road. But to describe motion fully you need more — how fast that number is changing (velocity) and how fast that is changing (acceleration). These three quantities are the vocabulary of all motion: position says where, velocity says how fast and which way, acceleration says how the speed or direction is changing.
The key idea connecting them is simple: velocity is the rate of change of position, and acceleration is the rate of change of velocity. On a graph, each one is the slope of the one before it. Get comfortable with that picture and the formulas of the next lessons will feel obvious rather than memorized.
Position and displacement
Position tells you where an object is, measured from a chosen origin along an axis. It can be negative: if the origin is a doorway and rightward is positive, a point 3 m to the left of the doorway has .
Displacement is the change in position:
Displacement is not the same as distance travelled. Walk 5 m right, then 5 m left: distance travelled is 10 m, but displacement is because you ended where you started. Displacement only cares about start and end points.
Example 1. Distance versus displacement A cyclist starts at , rides to , then backs up to . Find the distance travelled and the displacement.
Distance travelled: from 2 m to 14 m is , then back from 14 m to 9 m is .
Displacement uses only start and end:
The displacement is positive, so the net motion was to the right.
Velocity: average and instantaneous
Average velocity is displacement divided by time:
Its unit is m/s, and its sign is the sign of the displacement: negative velocity means motion in the negative direction.
The instantaneous velocity is the average velocity over a time interval shrunk to almost zero — in words, the slope of the position–time graph at that moment. (Calculus makes this precise with a derivative; here the graphical picture is enough.) A speedometer reads the magnitude of this quantity: the instantaneous speed. Speed has no direction, so a speedometer cannot tell you whether you are moving forward or backward — velocity can.
Speed is the magnitude of velocity, always non-negative. A car moving left at has velocity and speed .
Example 2. Average velocity versus average speed A jogger runs 300 m east in 60 s, then 100 m west in 40 s. Taking east as positive, find her average velocity and her average speed.
Displacement: .
Total time: .
Average speed uses total distance:
The two answers differ because average velocity uses displacement while average speed uses distance.
Acceleration
Acceleration is the rate of change of velocity:
Its unit is m/s², meaning "meters per second, per second": an acceleration of means the velocity changes by every second.
Acceleration is about velocity, not speed. It is positive when velocity is becoming more positive, negative when velocity is becoming more negative. So a car braking while moving right (velocity positive and shrinking) has negative acceleration, even though it is slowing down. On a velocity–time graph, acceleration is the slope.
Example 3. A sign students get wrong A ball rolls up a ramp, taken as the positive direction. At its velocity is ; at it is momentarily at rest. Find its acceleration.
Start from the definition and substitute:
The acceleration is negative because the velocity is decreasing. The ball slows down, stops, and (if the acceleration stays ) then speeds up in the negative direction — moving back down the ramp. Note that the ball was slowing down the whole time even though it stopped at .
Reading motion graphs
The three graphs — position–time, velocity–time, acceleration–time — tell the same story three ways:
- Slope of the – graph = velocity. A straight, rising line means constant positive velocity.
- Slope of the – graph = acceleration. A horizontal – line means zero acceleration (constant velocity).
- The area under a – graph gives displacement (areas below the axis count as negative).
Example 4. Displacement from a velocity–time graph A cart has velocity for 5 s, then slows steadily to over the next 3 s. What is the total displacement, and what is the acceleration during the second phase?
Displacement is the area under the – graph: a rectangle plus a triangle.
Acceleration in the second phase:
Negative, as expected for slowing down in the positive direction.
Rearranging the definitions before plugging in numbers
The defining equations can be solved for any quantity. Rearranging symbolically first keeps the algebra clean and the units honest.
Starting from :
- Multiply both sides by : , so .
- Divide both sides by : — useful when you know how much the velocity must change and how fast it changes.
Example 5. Solve for time symbolically, then substitute A train travelling at slows uniformly and stops in . Find its acceleration.
Start from the definition:
Substitute the values:
Check the sign: the train moves in the positive direction and slows, so negative acceleration is correct.
Common mistakes
- Confusing distance with displacement: distance is the total path length, displacement is final position minus initial position and can be zero or negative.
- Reading a speedometer and calling it velocity: it shows instantaneous speed (magnitude only); velocity also carries a direction or sign.
- Using (average speed) when velocity is changing — that formula only gives the average over the whole interval, not the velocity at any instant.
- Thinking negative acceleration always means slowing down: a ball thrown downward (negative direction, speeding up) has negative acceleration while its speed increases; what matters is whether and have the same sign.
- Mixing units, e.g. dividing km by seconds or minutes by hours — convert everything to SI (m, s, m/s) before computing.
Practice
- A robot starts at position on a straight track (positive direction to the right) and ends at . What is its displacement?
- A cyclist rides 600 m north in 120 s, then 200 m south in 50 s. Taking north as positive, find her average velocity in m/s.
- A car moving in the positive direction slows uniformly from to in . What is its acceleration?
- An object has a constant acceleration of . If its velocity is at (positive direction defined to the right), how long does it take to reach a velocity of ?
- A cart moves with velocity for , then decelerates uniformly to rest over the next . Find the total displacement (use the area under the velocity–time graph).
Answers
- , positive meaning net motion to the right.
- north.
- ; negative because the velocity decreases.
- .
- Rectangle plus triangle , total in the positive direction.
Next lesson: when acceleration is constant, the definitions combine into the three standard constant-acceleration equations that solve most motion problems directly.